Roofing insulation is important in every house especially in areas with long hot climate season. This is important in reducing heat and moist build up in the roofing and the attic which can eventually lead to faster degradation of your house. If you are concerned about the attic insulation cost then you must be more concerned about the possible colossal costs that you are going to spend on repairs in the event of damaged roofing as a result of massive moist and heat build up.
Aside from that, having fully insulated attic roofing can also give you huge savings in energy costs especially if it is used as rooms that are regularly occupied. In this case, it is imperative to install proper insulation on the attic roof. This is important considering that the space between the ceiling and the roof is usually not sufficient enough to allow proper airflow that can effectively minimize intense heat from entering the room.
Evaluate the Types and Amount You Should Add
Warm air has a tendency to naturally shift to cooler areas. Heat is exchanged between the inside air and the outside air in an attic. Warm air is leaked outside the house into the cooler climate when there is no proper insulation, while the hot air from outside come into the house on warm days. Your central air conditioning system can experience remarkable stress from this exchange and can consume a lot of energy. An ideal solution would be to insulate the attic. The attic is often farthest away from the central air conditioning system therefore it is hotter than the other parts of the house. This can control the intense temperature in the attic and create a comfortable place. Attic insulation costs are as follows (cost is likely to vary based on several factors):
The most commonly used and cheapest insulating material for homes is loose fill fibreglass. Mineral wool and cellulose are other insulating materials. Cellulose supply acoustical insulation and high thermal and is the main eco-friendly alternative. Batts/roll insulation comes in resources such as rock wool, cellulose and fibreglass and is slightly more expensive than loose fill. It is advised that you use the services of a professional to do the task if you choose loose fill insulation. For this type of insulation, the cost would be about USD 300 – USD 600 for an average- sized attic.
Another factor that determines the cost for attic insulation is the R-value or the resistance of the material. The higher the R value of the material, the more effective it will be at insulating. Naturally, the cost of insulation increases when the R value increases. Attics and other high rise ceilings like those of cathedrals demand a greater level R value than walls.
Attic Insulation That Stays Forever Young
Your single option is roll out batting if you choose the attic insulation. For this choice, you will possibly spend approximately USD 100 – USD 500. Again, the size of attic, cost of material, and R value and other factors are sure to have an effect on the actual cost. Professional service is required for blow insulation which places the loose fill substance into the roof, wall or ceiling of the attic. Attic insulation in this case would cost about USD 2 – USD 3.50 per square foot. Hence, the approximate calculation for insulation using this method is about USD 2000 – USD 3500 for insulating a 1000 sq ft area.
In most cases, it is better to make initial investment on the attic insulation cost because this is usually more cost-effective in the end. Aside from that, it offers utmost comfort to the attic room occupants on top of getting huge savings on energy bills.
When calculating for the cost of the attic insulation, there are several factors that must be considered in order to arrive at more precise calculation. Firstly, you need to identity the R factor or the R value in your locality. This is a fixed data determined and set by the energy regulation body in your area.
Take note that this factor can vary from one region to another. The figure is largely affected by the type of climate in your area. Colder climate has higher R value, while hot climate areas usually have lower value. This value tells you if the insulation is sufficient enough to provide comfort when occupying the place. Higher value means that the insulation works in minimizing heat build up. Meanwhile lower value means that you need to have insulation in order to reduce heat. For this reason, it is suggested to ask for the standard figure that is applied in your place.
Aside from identifying the R value, you must also calculate for the total area that needs to be insulated. This is important in getting the projected cost of insulating the entire attic. Moreover, you must further decide on the kind of insulating materials that you want to use. There are several types for you to choose from; such as blanket batts and rolls, foam board, loose-fill, reflective system, and structural insulating panels among many others.
Each type has different price, and they also have different styles with unique quality. Keep in mind that some of these types are not best for roofing but ideal for walls. That is why you need select the right type of insulating materials that fit well to your planned use and budget. In conclusion, in order to compute for the attic insulation cost, there is no definite amount because it is dependent on several factors as mentioned herein.